top of page

Quality Control in Home and Technical Textiles: Which Defects to Look For and How to Document Them

Nov 11
5 min read
Wide light-blue home textile fabric on the left, a dark technical fabric roll with a stain and a barcode tag on the right — quality control in home and technical textiles
In home textiles the question is where the defect is; in technical textiles, whether it is on record.

Home textiles and technical textiles can run through the same quality control line, but the hard part of inspection sits in a different place in each segment. On wide-width fabrics such as bedding, sheeting and curtain fabric, the question is where the defect is: a fine defect in the middle of the width is easy to miss. On seat upholstery, coated and technical fabrics, the question is whether the defect is on record: these fabrics go to buyers who ask for traceable quality on every roll.

 

This article continues our post on fabric quality control by fabric type, where we covered knitted, denim and woven fabric. Here we look at which defects matter in the two segments, how Serkon.AI Q2 detects and records them, and how each roll is documented with its report. For defect names in detail, see our fabric defects guide.

 

Two segments, two different questions

Segment

What makes inspection hard

Defects most often looked for

The buyer's question

Home textiles (bedding, sheeting, curtain fabric)

Wide width; a fine defect in the middle of the width is easy to miss

Thick pick, broken pick, warp streak, stain, hole, shade variation across the width

"Where will the defect show up at cutting?"

Technical and automotive textiles (seat upholstery, coated and technical fabric)

The buyer asks for traceable quality on every roll; the defect has to be on record

Stain, hole, contaminating fibre, thick place

"What shows the quality of this roll?"

 

1. Home textiles: on a wide width, defects hide in the middle

Fabrics such as bedding and sheeting are produced in wide widths. At this width, a fine defect in the middle of the fabric, such as a thick pick or a short warp streak, is easy to miss — and may only surface at cutting or at the customer. On light, plain dyed grounds a small stain can follow the same path.

 

Serkon.AI Q2 detects 30+ defect types in real time across the full fabric width and records every defect with its roll, position and type. The defect position appears on the width map before cutting, so the cutting room knows the defective area while it plans the cut.

 

On a wide width, the color question is shade variation across the width (left, center, right). When Colortron is added on the same line, this variation is measured at the left, center and right of the fabric width and monitored continuously along the roll; Q2 handles defect detection, Colortron handles color control. We explain color measurement in detail in our color control post.

 

Patterned and printed fabrics are also common in home textiles. With Q2, plain dyed grounds are preferred; development continues on patterned and printed fabrics. Whether the fabric on your line fits is something we see together in a pre-assessment with your own fabric.


A fine crosswise defect marked with a ring in the middle of a wide fabric, with the width map below showing the defect position
Defects hide in the middle of the fabric; their position appears on the width map before cutting. 

2. Technical and automotive textiles: a defect is not only found — it is documented

Seat upholstery, coated and technical fabrics go to buyers who ask for traceable quality on every roll. In this segment it is not enough to find a stain, a hole, a contaminating fibre or a thick place; it has to be on record with its position. The defect belongs in the record, not in someone's memory.

 

Serkon.AI Q2 runs on automotive and technical textile lines; it detects 30+ defect types in real time and records every defect with its roll, position and type. Every roll leaves the line with its own report, ready for the buyer's file.

 

On technical fabric, whether a defect repeats matters as much as its type. The defect distribution shows which type comes how often; a recurring defect type tells you where to start the root-cause search.

 

How it is documented: what is in every roll report?

A fabric roll with a barcode tag next to a roll report diagram with defect list, width map, defect distribution and barcode
Every roll leaves with its own report: defect list, width map, defect distribution and barcode.

 

Every roll that passes inspection leaves the line with its own report. The report has four parts:

 

  • Defect list: Every detected defect, with its roll, position and type.

  • Fabric width map: Where the defects sit across the width, and in which zone between the left edge, the middle and the right edge they cluster.

  • Defect distribution: Which defect type comes how often.

  • Barcode: After inspection the system generates a barcode that identifies the inspection content; the information travels with the roll.

 

If Colortron runs on the same line, the roll's ΔE value and lot are included in the same record. The report is exported / integrated to your ERP, so production planning, shipping and customer reporting read quality data from the same source. When a buyer asks "was that defect really there?", the answer is not a memory but a record with a roll number, a position and a type. For the whole process, see the 7 stages of the quality control process.

 

What both segments share: the standard lives in the system, not in the person

In home textiles and technical textiles alike, the value of inspection comes from its consistency. The system marks defects the same way, regardless of operator or working hours. The operator does not disappear — the role evolves: instead of scanning the fabric by eye, they review detections and approve the final quality decision. The quality standard stays in the system, not in the person.

 

As a plug-in on your existing inspection machine

Q2 works as a plug-in on your existing inspection machine, without changing operating habits. Installation takes 1–3 working days after delivery, operator training 5–10 working days. Depending on line speed you can choose Q2 (50+ m/min) or Q2 Lite (up to 30 m/min). Which machines it fits and the installation steps are covered in our retrofit guide.

 

Proof is not an opinion — it is data.

 

Which fabric should we start with on your line?

Bedding, upholstery or technical fabric: tell us which fabric you inspect, your fabric width and your line speed, and we will plan a live pre-assessment with your own fabric. You will see the results together with a defect map and a sample roll report.

 




Short FAQ


Does Q2 work on home textile fabrics?

Q2 runs on plain woven and knitted grounds; plain dyed fabrics such as bedding and sheeting fall within this scope. Development continues on patterned and printed fabrics.

Q2 detects 30+ defect types in real time across the full fabric width. Every defect is recorded with its roll, position and type, and its position appears on the width map before cutting.

Every detected defect is recorded with its roll, position and type. Each roll report contains a defect list, a fabric width map, a defect distribution and a barcode; the report is exported / integrated to your ERP.

Q2 handles defect detection; for shade variation, Colortron is added on the same line. Colortron measures at the left, center and right of the fabric width, works under standard D65 light with repeatable precision up to ΔE 0.05, and lots every roll against its ΔE reference.

No. Q2 works as a plug-in on your existing inspection machine, without changing operating habits. Installation takes 1–3 working days after delivery, training 5–10 working days.

For the other fabric types, see our post on knitted, denim and woven fabric; for defect names, see the 30 defects guide.

whatsapp-icon.png
bottom of page